-
ASTM A125 – Standard Specification for Steel Springs, Helical, Heat-Treated
ASTM A125 Helical Spring Testing
ASTM A125 – This specification covers hot-coiled, heat-treated helical compression springs with tapered, closed, squared and ground ends made of
hot-wrought round steel bars 3/8 in. (9.5 mm) and larger… -
ASTM C1135 – Standard Test Method for Determining Tensile Adhesion Properties of Structural Sealants
ASTM C1135 – This test method covers a laboratory procedure for quantitatively measuring the tensile adhesion properties of structural sealants, hereinafter
referred to as the “sealant”.
Please Contact With Us For More…
-
ASTM C273 – Standard Test Method for Shear Properties of Sandwich Core Materials
ASTM C273 – This test method covers the determination of shear properties of sandwich construction core materials associated with shear distortion of
planes parallel to the facings.
Please Contact With Us For…
-
ASTM C633 – Standard Test Method for Adhesion or Cohesion Strength of Thermal Spray Coatings
ASTM C633 – This test method covers the determination of the degree of adhesion (bonding strength) of a coating to a substrate or the cohesion strength of the
coating in a tension… -
ASTM D3032 – Standard Test Methods for Hookup Wire Insulation
Dynamic Cut – Through Test Fixture
ASTM D3032 – This test method covers procedures for testing hookup wire.
Please Contact With Us For More Information
-
ASTM D412 – Standard Test Methods for Vulcanized Rubber and Thermoplastic Elastomers—Tension
ASTM D412 Rubber Tensile Test Fixture
ASTM D412 – This test method covers procedures used to evaluate the tensile (tension) properties of vulcanized thermoset rubbers and thermoplastic elastomers.
These methods are not applicable… -
ASTM D4501 – Standard Test Method for Shear Strength of Adhesive Bonds Between Rigid Substrates by the Block-Shear Method
ASTM D4501 – Block-Shear Strength Test
ASTM D4501 – This test method describes a procedure and fixture used to determine shear strengths of adhesives used to bond materials with moduli higher thanthe…
-
ASTM D5450 – Standard Test Method for Transverse Tensile Properties of Hoop Wound Polymer Matrix Composite Cylinders
Transverse Tensile Properties of Hoop Wound Polymer Matrix Composite Cylinders
ASTM D5450 – This test method determines the transverse tensile properties of wound polymer matrix composites reinforced by high-modulus continuous fibers.
It describes…
-
ASTM D6195 – Standard Test Methods for Loop Tack
ASTM D6195 specifies a few procedures to measure quick stick adhesive strength.
This test is different from a peel test because the tape is not given enough time or pressure to fully…
-
ASTM D624 – Standard Test Method for Tear Strength of Conventional Vulcanized Rubber and Thermoplastic Elastomers
ASTM D624 – This test method describes procedures for measuring a property of conventional vulcanized rubber and thermoplastic elastomers called tear strength.
Vulcanized rubber and thermoplastic elastomers (TPE) often fail in service…
-
ASTM D6671 – Standard Test Method for Mixed Mode I-Mode II Interlaminar Fracture Toughness of Unidirectional Fiber Reinforced Polymer Matrix Composites
MIXED-MODE BENDING FRACTURE TOUGHNESS
ASTM D6671 – This test method covers the determination of interlaminar fracture toughness, Gc, of continuous fiber-reinforced composite materials at various Mode
I to Mode II loading ratios using the… -
ASTM D732 – Standard Test Method for Shear Strength of Plastics by Punch Tool
ASTM D732 – Shear Punch Tool
ASTM D732 – This test method covers the procedure for determining the shear strength of plastics in the form of sheets, plates, and molded shapes in
thicknesses from…
- TR | EN
- Tel : +90 (312) 394 28 68
- WhatsApp: +90 (546) 437 05 06