Standartlar | Page 24 of 34 | ParsRos Malzeme Test Cihazları

ISO 11040-4 Fixtures for Testing Pre-filled Glass Syringes

0 out of 5

This ISO standard applies to Tubing-glass barrels (single-chamber design) for injection preparations, and sterilized subassembled syringes ready for filling.

Bilgi Almak İçin Lütfen Bizimle İletişime Geçiniz
ISO 11608-3 Needle Based Injection System Testing

0 out of 5

ISO 11608-3-specifies the functional and design considerations for containers to be used with needle-based injection systems (NIS) that fulfil the specifications

of ISO 11608-1.

Bilgi Almak İçin Lütfen Bizimle İletişime Geçiniz
ISO 11644 – Test for Adhesion of Finish

0 out of 5

ISO 11644 specifies a method for measuring the adhesion of the finish to leather or the adhesion between two adjacent layers of the finish.

Bilgi Almak İçin Lütfen Bizimle İletişime Geçiniz
ISO 11782 – A Metal Corrosion Fatigue Testing

0 out of 5

This ISO Standard provides instruction on corrosion fatigue testing of metals and alloys in aqueous or gaseous environments and is concerned with cycles to failure testing.

Bilgi Almak İçin Lütfen Bizimle
ISO 12106 – Metallic Materials Axial-Strain-Control Fatigue Testing

0 out of 5

ISO 12106 specifies a method of testing uniaxially loaded specimens under strain control at constant amplitude, uniform temperature and a strain ratio of

R = -1. Low cycle fatigue tests.

Bilgi Almak…
ISO 12108 Test Fikstürü

0 out of 5

This ISO Standard describes tests for determining the fatigue crack growth rate from the fatigue crack growth threshold stress-intensity factor range to the onset of rapid,

unstable fracture.

Bilgi Almak İçin Lütfen…
ISO 12111 – Strain Controlled Thermomechanical Fatigue Testing Method of Metals

0 out of 5

ISO 12111 is applicable to the TMF testing of uniaxially loaded metallic specimens under strain control.

Bilgi Almak İçin Lütfen Bizimle İletişime Geçiniz
ISO 12135 Test Fikstürü

0 out of 5

This ISO standard specifies methods for determining fracture toughness in terms of K, ?, J and R-curves for homogeneous metallic materials subjected to quasistatic loading

Bilgi Almak İçin Lütfen Bizimle İletişime Geçiniz
ISO 12192 – Ring Crush Method

0 out of 5

ISO 12192 specifies a method for the determination of the edgewise compressive strength (ring crush resistance) of paper and paperboard, especially board used in the

manufacture of fibreboard shipping containers.

Bilgi Almak…
ISO 12236 – Static Puncture Test (CBR Test)

0 out of 5

ISO 12236 specifies a method for the determination of the puncture resistance by measuring the force required to push a flat-ended plunger through geosynthetics.

Bilgi Almak İçin Lütfen Bizimle İletişime Geçiniz
ISO 12625-5 Wet Tensile Strength of Tissue Products

0 out of 5

ISO 12625-5 specifies a test method for the determination of the wet tensile strength of tissue paper and tissue products after soaking with water, using a tensile-strength

testing apparatus operating with…
ISO 12625-9 Test Fikstürü

0 out of 5

ISO 12625-9 specifies a test method for the determination of the resistance to mechanical penetration (ball burst strength procedure) of tissue paper and tissue products.

Bilgi Almak İçin Lütfen Bizimle İletişime Geçiniz