Standartlar | Page 37 of 38 | ParsRos Malzeme Test Cihazları

ISO 9073-7 Bending Length of Nonwowens Textiles

0 out of 5

ISO 9073-7 specifies a method for the determination of the bending length of nonwovens. Gives an equation for calculating the flexural rigity of the fabric from the bending length.

Bilgi Almak…
ISO 9187-1 Injection Equipment for Medical Use

0 out of 5

ISO 9187-1 specifies materials, dimensions, capacities, performance and packaging requirements for three forms of glass ampoule (forms B, C and D) for injectable

pharmaceutical products.

Bilgi Almak İçin Lütfen Bizimle İletişime Geçiniz
ISO 9311-2 Shear Strength of Adhesives

0 out of 5

This ISO standard specifies a method for the determination of the shear strength of joints made with adhesives for thermoplastic piping systems.

Bilgi Almak İçin Lütfen Bizimle İletişime Geçiniz
ISO 9626 – Stainless Steel Needle Tubing for the Manufacture of Medical Devices

0 out of 5

ISO 9626 applies to rigid stainless steel needle tubing suitable for use in the manufacture of hypodermic needles and other medical devices primarily for human use.

Bilgi Almak İçin Lütfen Bizimle
ISO/IEC 10373-1 Cards and Security Devices for Personal Identification

0 out of 5

ISO/IEC 10373-1 the test methods for characteristics of identification cards according to ISO/IEC 7810 and other standards, such as those listed in the Introduction.

Bilgi Almak İçin Lütfen Bizimle İletişime Geçiniz
ISO/IEC 7810 – Physical Characteristics of Identification Cards

0 out of 5

ISO/IEC 7810 describes the characteristics for identification cards and the use of such cards for international interchange.

Bilgi Almak İçin Lütfen Bizimle İletişime Geçiniz
ISO/TS 11405 – Testing of Adhesion to Tooth Structure

0 out of 5

This ISO standard gives guidance on substrate selection, storage, and handling as well as essential characteristics of different test methods for quality testing of

the adhesive bond between restorative dental materials…
ISO/TS 19736 – Bonding Test Between Polymer Teeth and Denture Base Materials

0 out of 5

ISO/TS 19736 specifies a test method for bonding of polymer teeth to denture base materials.

Bilgi Almak İçin Lütfen Bizimle İletişime Geçiniz
NASM 1312-13 Test Fikstürü

0 out of 5

The Aerospace Industries Association publishes NASM 1312-13, Fastener Test Methods for Double Shear Tests.

Bilgi Almak İçin Lütfen Bizimle İletişime Geçiniz
NASM 1312-20 Test Fikstürü

0 out of 5

MIL-STD-1312-20 / NASM 1312-20 – These fixtures are used to test, in single shear, fasteners (typically metallic) which are not long enough to be tested in double shear.

Bilgi Almak İçin…
TAPPI T 456 Test Fikstürü

0 out of 5

TAPPI T 456 describes the procedure for the determination of the tensile strength of paper and paperboard after saturation with water.

Bilgi Almak İçin Lütfen Bizimle İletişime Geçiniz
TAPPI T 549 Test Fikstürü

0 out of 5

TAPPI T 549 describes a horizontal plane procedure for the determination of the coefficient of static and kinetic friction of paper measured when sliding against itself.

Bilgi Almak İçin Lütfen Bizimle